Menu
Your Cart

T SLOTTER & SLAT WALL CUTTER 28MMX4MM 1/2' SHANK

T SLOTTER & SLAT WALL CUTTER 28MMX4MM 1/2' SHANK
T SLOTTER & SLAT WALL CUTTER 28MMX4MM 1/2' SHANK
  • Stock: In Stock
  • Model: KP103510
  • Weight: 0.14kg
  • Dimensions: 32.00cm x 86.00cm x 86.00cm
  • SKU: KP103510
  • UPC: 6009675088799
190 samples sold
Product Views: 49
R 962.95
Ex Tax: R 837.35
Pro-Tech. South African favourite for over 30 YearsWall display T-slot cutters

T-slot router bit sampleT-slot bit

These T-slot cutters will allow you to cut both the groove as well as the wider slot in one pass. A carbide cutting edge is part of the neck of the router bit. The anti-kickback design allows for better performance and reduced vibration under cutting load.

  • Designed for creating T-slot wall panels and many other useful purposes.
  • Build your own sturdy and attractive slotted wall to display workshop tools – hanging by a hook.
  • Cuts all composition materials, hardwoods, plywood and softwoods.

Profile 

This router bit design is intended for use in router tables and work great in CNC routers. This router bit is not designed for plunging operations.

This router bit has a 12,7 mm shank (shaft) that will fit most large routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.

 

PRO-TECH router bits are manufactured in Taiwan.

Features and descriptions 

consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection – clean and scratch free
  • Hearing protection – quality earmuffs
  • Dust masks – discard old and dirty masks
  • Gloves – for easy handling of material and hand protection
Wear Gloves Eye Protection Hearing Protection Dust Mask
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

Router Table Safety

Although most router bits are small, they can be potentially dangerous and should deserve your attention and respect.

Push blocks and safety devices1 Use push sticks or a push block to position your hands a safe distance from the router bit.

2 Use large-diameter bits only in a router table. Using bits over 25mm Ø (diameter) in a handheld router can possibly cause you to lose control of the tool and harm yourself or bystanders.

3 Always wear a dust mask as well as eye and hearing protection.

4 Take light cuts. Heavy cuts invite kickback. If necessary, move the fence closer to the bit or switch to a larger guide bearing/bush.

5 Use a featherboard (anti-kickback device) to support the workpiece against the router table and/or fence.

6 Never climb-cut. Always feed the stock from right to left. Against the rotation of the router bit. (see illustration)

7 Avoid routing small stock. Instead, rout a larger piece and cut it to size afterwards. If you absolutely have to profile a small piece, build an suitable jig or secure the workpiece.

8 Always use a guard. If the fence didn’t come with a guard, make your own.

9 Never start the router with the bit in contact with the material.

10 Don’t force the router bit or overload the router. Excessive heat is an enemy.

11 Secure/fasten the router in the base before starting/switch on the router.

Router bit to collet fit12 Don’t bottom out the bit in the collet or partially insert the bit. Instead, completely insert the bit, and then back off approximately 2 mm. At least 2/3 's of the router bit shank should be inside the collet.

13 Be sober and not under the influence of medicine that causes a lack of concentration

14 Tidy up your workshop to ensure the ability to move freely with enough room around the router table

Part No. Shank dia. Cutting width of the slot Cutting width of the groove Cutting Height
KP103510 1/2 inch 28 mm 11,2 mm 4 mm

 

 

Take CareFull Speed

 

Write a review

Note: HTML is not translated!
Bad Good